Etaamb.openjustice.be
Koninklijk Besluit
gepubliceerd op 11 juni 2018

Bureau voor Normalisatie . - Registratie van Belgische normen 1. Overeenkomstig artikel 26 van het koninklijk besluit van 25 oktober 2004 betreffende de bekrachtiging en de registratie van de door het Bureau voor normalisatie openbaar gemaa(...) NBN EN 12261:2018 Gas meters - Turbine gas meters vervangt NBN EN 12261:2002 (1e uitgave), NB(...)

bron
federale overheidsdienst economie, k.m.o., middenstand en energie
numac
2018012510
pub.
11/06/2018
prom.
--
staatsblad
https://www.ejustice.just.fgov.be/cgi/article_body(...)
Document Qrcode

FEDERALE OVERHEIDSDIENST ECONOMIE, K.M.O., MIDDENSTAND EN ENERGIE


Bureau voor Normalisatie (NBN). - Registratie van Belgische normen 1. Overeenkomstig artikel 26 van het koninklijk besluit van 25 oktober 2004Relevante gevonden documenten type koninklijk besluit prom. 25/10/2004 pub. 09/11/2004 numac 2004011453 bron federale overheidsdienst economie, k.m.o., middenstand en energie Koninklijk besluit betreffende de uitvoeringsmodaliteiten van de normalisatieprogramma's evenals de bekrachtiging of registratie van normen type koninklijk besluit prom. 25/10/2004 pub. 10/11/2004 numac 2004014235 bron federale overheidsdienst mobiliteit en vervoer Koninklijk besluit tot wijziging van het koninklijk besluit van 13 september 1998 houdende havenstaatcontrole en wijziging van het koninklijk besluit van 20 juli 1973 houdende zeevaartinspectiereglement en van het koninklijk besluit van 1 december 1999 inzake de registratie van de opvarenden van passagiersschepen sluiten betreffende de bekrachtiging en de registratie van de door het Bureau voor normalisatie openbaar gemaakte normen, kondigt dit Bureau de registratie aan van de hierna volgende Belgische normen: NBN EN 12261:2018 Gas meters - Turbine gas meters vervangt NBN EN 12261:2002 (1e uitgave), NBN EN 12261/A1:2006 (1e uitgave) NBN EN 12274-1:2018 Slurry surfacing - Test methods - Part 1: Sampling of slurry surfacing mixture vervangt NBN EN 12274-1:2002 (1e uitgave) NBN EN 12274-2:2018 Slurry surfacing - Test methods - Part 2: Determination of residual binder content including preparation of samples vervangt NBN EN 12274-2:2003 (1e uitgave) NBN EN 12274-3:2018 Slurry surfacing - Test methods - Part 3: Consistency vervangt NBN EN 12274-3:2002 (1e uitgave) NBN EN 12274-4:2018 Slurry surfacing - Test methods - Part 4: Determination of cohesion of the mix vervangt NBN EN 12274-4:2003 (1e uitgave) NBN EN 12274-5:2018 Slurry surfacing - Test method - Part 5: Determination of the minimum binder content and wearing resistance vervangt NBN EN 12274-5:2003 (1e uitgave) NBN EN 12274-6:2018 Slurry surfacing - Test methods - Part 6: Rate of application vervangt NBN EN 12274-6:2002 (1e uitgave) NBN EN 12814-4:2018 Testing of welded joints of thermoplastics semi-finished products - Part 4: Peel test vervangt NBN EN 12814-4:2001 (1e uitgave) NBN EN 12953-4:2018 Shell boilers - Part 4: Workmanship and construction of pressure parts of the boiler vervangt NBN EN 12953-4:2002 (1e uitgave) NBN EN 12977-1:2018 Thermal solar systems and components - Custom built systems - Part 1: General requirements for solar water heaters and combisystems vervangt NBN EN 12977-1:2012 (1e uitgave) NBN EN 12977-2:2018 Thermal solar systems and components - Custom built systems - Part 2: Test methods for solar water heaters and combisystems vervangt NBN EN 12977-2:2012 (1e uitgave) NBN EN 12977-3:2018 Thermal solar systems and components - Custom built systems - Part 3: Performance test methods for solar water heater stores vervangt NBN EN 12977-3:2012 (3e uitgave) NBN EN 12977-5:2018 Thermal solar systems and components - Custom built systems - Part 5: Performance test methods for control equipment vervangt NBN EN 12977-5:2012 (1e uitgave) NBN EN 13016-1:2018 Liquid petroleum products - Vapour pressure - Part 1: Determination of air saturated vapour pressure (ASVP) and calculated dry vapour pressure equivalent (DVPE) vervangt NBN EN 13016-1:2007 (2e uitgave) NBN EN 13016-3:2018 Liquid petroleum products - Vapour pressure - Part 3: Determination of vapour pressure and calculated dry vapour pressure equivalent (DVPE) (Triple Expansion Method) NBN EN 1305:2018 Inland navigation vessels - Connections for the discharge of oily mixture vervangt NBN EN 1305:1996 (1e uitgave) NBN EN 1306:2018 Inland navigation vessels - Connections for the discharge of waste water vervangt NBN EN 1306:1996 (1e uitgave) NBN EN 1307:2014+A2:2018 Textile floor coverings - Classification vervangt NBN EN 1307:2014+A1:2016) NBN EN 13077:2018 Devices to prevent pollution by backflow of potable water - Air gap with non-circular overflow (unrestricted) - Family A - Type B vervangt NBN EN 13077:2008 (2e uitgave) NBN EN 1329-1:2014+A1:2018 Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Unplasticized poly(vinyl chloride) (PVC-U) - Part 1: Specifications for pipes, fittings and the systems vervangt NBN EN 1329-1:2014 (2e uitgave) NBN EN 13361:2018 Geosynthetic barriers - Characteristics required for use in the construction of reservoirs and dams vervangt NBN EN 13361:2013 (2e uitgave) NBN EN 13362:2018 Geosynthetic Barriers - Characteristics required for use in the construction of canals vervangt NBN EN 13362:2013 (2e uitgave) NBN EN 13445-1:2014/A2:2018 Unfired pressure vessels - Part 1: General NBN EN 13445-3:2014/A4:2018 Unfired pressure vessels - Part 3: Design NBN EN 13476-1:2018 Plastics piping systems for non-pressure underground drainage and sewerage - Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) - Part 1:General requirements and performance characteristics vervangt NBN EN 13476-1:2007 (1e uitgave) NBN EN 13476-2:2018 Plastics piping systems for non-pressure underground drainage and sewerage - Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) - Part 2: Specifications for pipes and fittings with smooth internal and external surface and the system, Type A vervangt NBN EN 13476-2:2007 (1e uitgave) NBN EN 13476-3:2018 Plastics piping systems for non-pressure underground drainage and sewerage - Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) - Part 3: Specifications for pipes and fittings with smooth internal and profiled external surface and the system, Type B vervangt NBN EN 13476-3+A1:2009 (1e uitgave) NBN EN 13491:2018 Geosynthetic barriers - Characteristics required for use in the construction of tunnels and associated underground structures vervangt NBN EN 13491:2013 (2e uitgave) NBN EN 13492:2018 Geosynthetic barriers - Characteristics required for use in the construction of liquid waste disposal sites, transfer stations or secondary containment vervangt NBN EN 13492:2013 (2e uitgave) NBN EN 13493:2018 Geosynthetic barriers - Characteristics required for use in the construction of solid waste storage and disposal sites vervangt NBN EN 13493:2013 (2e uitgave) NBN EN 13757-2:2018 Communication systems for meters - Part 2: Wired M-Bus communication vervangt NBN EN 13757-2:2005 (1e uitgave) NBN EN 13757-3:2018 Communication systems for meters - Part 3: Application protocols vervangt NBN EN 13757-3:2013 (2e uitgave) NBN EN 13757-7:2018 Communication systems for meters - Part 7: Transport and security services vervangt NBN EN 13757-3:2013 (2e uitgave) NBN EN 1431:2018 Bitumen and bituminous binders - Determination of residual binder and oil distillate from bitumen emulsions by distillation vervangt NBN EN 1431:2009 (2e uitgave) NBN EN 14511-1:2018 Air conditioners, liquid chilling packages and heat pumps for space heating and cooling and process chillers, with electrically driven compressors - Part 1: Terms and definitions vervangt NBN EN 14511-1:2013 (4e uitgave) NBN EN 14511-2:2018 Air conditioners, liquid chilling packages and heat pumps for space heating and cooling and process chillers, with electrically driven compressors - Part 2: Test conditions vervangt NBN EN 14511-2:2013 (4e uitgave) NBN EN 14511-3:2018 Air conditioners, liquid chilling packages and heat pumps for space heating and cooling and process chillers, with electrically driven compressors - Part 3: Test methods vervangt NBN EN 14511-3:2013 (4e uitgave) NBN EN 14511-4:2018 Air conditioners, liquid chilling packages and heat pumps for space heating and cooling and process chillers, with electrically driven compressors - Part 4: Requirements vervangt NBN EN 14511-4:2013 (4e uitgave) NBN EN 15382:2018 Geosynthetic barriers - Characteristics required for use in transportation infrastructure vervangt NBN EN 15382:2013 (2e uitgave) NBN EN 1568-3:2018 Fire extinguishing media - Foam concentrates - Part 3: Specification for low expansion foam concentrates for surface application to water-immiscible liquids vervangt NBN EN 1568-3:2008 (2e uitgave) NBN EN 16205:2013+A1:2018 Laboratory measurement of walking noise on floors vervangt NBN EN 16205:2013 (1e uitgave) NBN EN 16668:2016+A1:2018 Industrial valves - Requirements and testing for metallic valves as pressure accessories vervangt NBN EN 16668:2016 NBN EN 16729-3:2018 Railway applications - Infrastructure - Non-destructive testing on rails in track - Part 3: Requirements for identifying internal and surface rail defects NBN EN 16785-2:2018 Bio-based products - Bio-based content - Part 2: Determination of the bio-based content using the material balance method NBN EN 16837:2018 Surfaces for sports areas - Determination of linear shoe/surface friction NBN EN 16993:2018 Geosynthetic barriers - Characteristics required for use in the construction of storage lagoons, secondary containment (above and below ground) and other containment applications for chemicals, polluted water and produced liquids NBN EN 16994:2018 Clay Geosynthetic Barriers - Characteristics required for use in the construction of underground structures (other than tunnels and associated structures) NBN EN 1883:2018 Feather and down - Sampling in view of tests vervangt NBN EN 1883:1999 (1e uitgave) NBN EN 2795:2018 Aerospace series - Fluorocarbon rubber (FKM) - Low compressions set - Hardness 50 IRHD NBN EN 419212-4:2018 Application Interface for Secure Elements for Electronic Identification, Authentication and Trusted Services - Part 4: Privacy specific Protocols vervangt NBN EN 419212-2:2015 (1e uitgave), NBN EN 419212-1:2015 (1e uitgave) NBN EN 419212-5:2018 Application Interface for Secure Elements for Electronic Identification, Authentication and Trusted Services - Part 5: Trusted eService vervangt NBN EN 419212-1:2015 (1e uitgave), NBN EN 419212-2:2015 (1e uitgave) NBN EN 50496:2018 Determination of workers' exposure to electromagnetic fields and assessment of risk at a broadcast site NBN EN 50588-2:2018 Medium power transformers 50 Hz, with highest voltage for equipment not exceeding 36 kV - Part 2: Transformers with cable boxes on the high-voltage and/or low-voltage side - General requirements for transformers with rated power less than or equal to 3 150 kVA NBN EN 50588-3:2018 Medium power transformers 50 Hz, with highest voltage for equipment not exceeding 36 kV - Part 3: Transformers with cable boxes on the high-voltage and/or low-voltage side - Cable boxes type 1 for use on transformers meeting the requirements of EN 50588-2) NBN EN 50588-4:2018 Medium power transformers 50 Hz, with highest voltage for equipment not exceeding 36 kV - Part 4: Transformers with cable boxes on the high-voltage and/or low-voltage side - Cable boxes type 2 for use on transformers meeting the requirements of EN 50588-2 NBN EN 60061-1:1993/A57:2018 Lamp caps and holders together with gauges for the control of interchangeability and safety - Part 1: Lamp caps NBN EN 60061-2:1993/A53:2018 Lamp caps and holders together with gauges for the control of interchangeability and safety - Part 2: Lampholders NBN EN 60061-3:1993/A54:2018 Lamp caps and holders together with gauges for the control of interchangeability and safety - Part 3: Gauges NBN EN 60068-2-69:2017/AC:2018-04 Environmental testing - Part 2-69: Tests - Test Te/Tc: Solderability testing of electronic components and printed boards by the wetting balance (force measurement) method NBN EN 60122-1:2003/A1:2018 Quartz crystal units of assessed quality - Part 1: Generic specification NBN EN 60310:2016/AC:2018-04 Railway applications - Traction transformers and inductors on board rolling Stock NBN EN 60598-2-4:2018 Luminaires - Part 2: Particular requirements - Section 4: Portable general purpose luminaires NBN EN 61215-2:2017/AC:2018-04 Terrestrial photovoltaic (PV) modules - Design qualification and type approval - Part 2: Test procedures NBN EN 61643-11:2012/A11:2018 Low-voltage surge protective devices - Part 11: Surge protective devices connected to low-voltage power systems - Requirements and test methods NBN EN 61810-1:2015/AC:2018-04 Electromechanical elementary relays - Part 1: General and safety requirements NBN EN 62271-100:2009/A2:2017/AC:2018-04 High-voltage switchgear and controlgear - Part 100: Alternating-current circuit-breakers NBN EN 62271-101:2013/A1:2018 High-voltage switchgear and controlgear - Part 101: Synthetic testing NBN EN 81-21:2018 Safety rules for the construction and installation of lifts - Lifts for the transport of persons and goods - Part 21: New passenger and goods passenger lifts in existing building vervangt NBN EN 81-21+A1:2012 (2e uitgave) NBN EN 81-58:2018 Safety rules for the construction and installation of lifts - Examination and tests - Part 58: Landing doors fire resistance test vervangt NBN EN 81-58:2003 (1e uitgave) NBN EN 9223-100:2018 Programme Management - Configuration Management - Part 100: A guide for the application of the principles of configuration management NBN EN 9223-101:2018 Programme Management - Configuration Management - Part 101: Configuration identification NBN EN 9223-102:2018 Programme Management - Configuration Management - Part 102: Configuration status accounting NBN EN 9223-103:2018 Programme Management - Configuration Management - Part 103: Configuration Verifications, Reviews and Audits NBN EN 9223-104:2018 Programme Management - Configuration Management - Part 104: Configuration Control NBN EN 9223-105:2018 Programme Management - Configuration Management - Part 105: Glossary NBN EN IEC 60051-5:2018 Direct acting indicating analogue electrical measuring instruments and their accessories - Part 5: Special requirements for phase meters, power factor meters and synchroscopes NBN EN IEC 60051-6:2018 Direct acting indicating analogue electrical measuring instruments and their accessories - Part 6: Special requirements for ohmmeters (impedance meters) and conductance meters NBN EN IEC 60051-7:2018 Direct acting indicating analogue electrical measuring instruments and their accessories - Part 7: Special requirements for multi-function instruments NBN EN IEC 60051-8:2018 Direct acting indicating analogue electrical measuring instruments and their accessories - Part 8: Special requirements for accessories NBN EN IEC 60068-3-5:2018 Environmental testing - Part 3-5: Supporting documentation and guidance - Confirmation of the performance of temperature chambers NBN EN IEC 60068-3-6:2018 Environmental testing - Part 3-6: Supporting documentation and guidance - Confirmation of the performance of temperature/humidity chambers NBN EN IEC 60099-5:2018 Surge arresters - Part 5: Selection and application recommendations NBN EN IEC 60191-1:2018 Mechanical standardization of semiconductor devices - Part 1: General rules for the preparation of outline drawings of discrete devices NBN EN IEC 60230:2018 Impulse tests on cables and their accessories NBN EN IEC 60370:2018 Test procedure for thermal endurance of insulating resins and varnishes for impregnation purposes - Electric breakdown methods NBN EN IEC 60512-15-2:2018 Connectors for electrical and electronic equipment - Tests and measurements - Part 15-2: Connector tests (mechanical) - Test 15b: Insert retention in housing (axial) NBN EN IEC 60512-8-3:2018 Connectors for electrical and electronic equipment - Tests and measurements - Part 8-3: Static load tests (fixed connectors) - Test 8c: Robustness of actuating lever NBN EN IEC 60598-2-17:2018 Luminaires - Part 2-17: Particular requirements - Luminaires for stage lighting, television and film studios (outdoor and indoor) NBN EN IEC 60749-12:2018 Semiconductor devices - Mechanical and climatic test methods - Part 12: Vibration, variable frequency NBN EN IEC 60749-26:2018 Semiconductor devices - Mechanical and climatic test methods - Part 26: Electrostatic discharge (ESD) sensitivity testing - Human body model (HBM) NBN EN IEC 60793-1-54:2018 Optical fibres - Part 1-54: Measurement methods and test procedures - Gamma irradiation NBN EN IEC 60942:2018 Electroacoustics - Sound calibrators NBN EN IEC 61076-2-111:2018 Connectors for electrical and electronic equipment - Product requirements - Part 2-111: Circular connectors - Detail specification for power connectors with M12 screw-locking NBN EN IEC 61076-3-119:2018 Connectors for electrical and electronic equipment - Product requirements - Part 3-119: Rectangular connectors - Detail specification for shielded and unshielded, free and fixed 10-way connectors with push-pull coupling for industrial environments for data transmission with frequencies up to 100 MHz NBN EN IEC 61125:2018 Insulating liquids - Test methods for oxidation stability - Test method for evaluating the oxidation stability of insulating liquids in the delivered state NBN EN IEC 61190-1-3:2018 Attachment materials for electronic assembly - Part 1-3: Requirements for electronic grade solder alloys and fluxed and non-fluxed solid solder for electronic soldering applications NBN EN IEC 61204-7:2018 Low-voltage switch mode power supplies - Part 7: Safety requirements NBN EN IEC 61249-2-45:2018 Materials for printed boards and other interconnecting structures - Part 2-45: Reinforced base materials clad and unclad - Non-halogenated epoxide non-woven/woven E-glass reinforced laminate sheets of thermal conductivity (1,0 W/m.K) and defined flammability (vertical burning test), copper-clad for lead-free assembly NBN EN IEC 61249-2-46:2018 Materials for printed boards and other interconnecting structures - Part 2-46: Reinforced base materials clad and unclad - Non-halogenated epoxide non-woven/woven E-glass reinforced laminate sheets of thermal conductivity (1,5 W/m.K) and defined flammability (vertical burning test), copper-clad for lead-free assembly NBN EN IEC 61249-2-47:2018 Materials for printed boards and other interconnecting structures - Part 2-47: Reinforced base materials clad and unclad - Non-halogenated epoxide non-woven/woven E-glass reinforced laminate sheets of thermal conductivity (2,0 W/m.K) and defined flammability (vertical burning test), copper-clad for lead-free assembly NBN EN IEC 61281-1:2018 Fibre optic communication subsystems - Part 1: Generic specification NBN EN IEC 61340-4-3:2018 Electrostatics - Part 4-3: Standard test methods for specific applications - Footwear NBN EN IEC 61340-4-4:2018 Electrostatics - Part 4-4: Standard test methods for specific applications - Electrostatic classification of flexible intermediate bulk containers (FIBC) NBN EN IEC 61340-4-5:2018 Electrostatics - Part 4-5: Standard test methods for specific applications - Methods for characterizing the electrostatic protection of footwear and flooring in combination with a person NBN EN IEC 61643-331:2018 Components for low-voltage surge protection - Part 331: Performance requirements and test methods for metal oxide varistors (MOV) NBN EN IEC 61643-352:2018 Components for low-voltage surge protection - Part 352: Selection and application principles for telecommunications and signalling network surge isolation transformers (SITs) NBN EN IEC 61754-7-2:2018 Fibre optic interconnecting devices and passive components - Fibre optic connector interfaces - Part 7-2: Type MPO connector family - Two fibre rows NBN EN IEC 61804-2:2018 Function blocks (FB) for process control and electronic device description language (EDDL) - Part 2: Specification of FB concept NBN EN IEC 61869-10:2018 Instrument transformers - Part 10: Additional requirements for low-power passive current transformers NBN EN IEC 61869-11:2018 Instrument transformers - Part 11: Additional requirements for low-power passive voltage transformers NBN EN IEC 62024-1:2018 High frequency inductive components - Electrical characteristics and measuring methods - Part 1: Nanohenry range chip inductor NBN EN IEC 62246-1-1:2018 Reed switches - Part 1-1: Generic specification - Blank detail specification NBN EN IEC 62271-110:2018/AC:2018-04 High-voltage switchgear and controlgear - Part 110: Inductive load switching NBN EN IEC 62343-5-2:2018 Dynamic modules - Part 5-2: Test methods - 1xN fixed-grid WSS - Dynamic crosstalk measurement NBN EN IEC 62443-4-1:2018 Security for industrial automation and control systems - Part 4-1: Secure product development lifecycle requirements NBN EN IEC 62559-3:2018 Use case methodology - Part 3: Definition of use case template artefacts into an XML serialized format NBN EN IEC 62561-2:2018 Lightning protection system components (LPSC) - Part 2: Requirements for conductors and earth electrodes NBN EN IEC 62561-6:2018 Lightning protection system components (LPSC) - Part 6: Requirements for lightning strike counters (LSC) NBN EN IEC 62561-7:2018 Lightning protection system components (LPSC) - Part 7: Requirements for earthing enhancing compounds NBN EN IEC 62604-2:2018 Surface acoustic wave (SAW) and bulk acoustic wave (BAW) duplexers of assessed quality - Part 2: Guidelines for the use NBN EN IEC 62613-1:2018 Plugs, socket-outlets and ship couplers for high-voltage shore connection systems (HVSC-Systems) - Part 1: General requirements NBN EN IEC 62613-2:2018 Plugs, socket-outlets and ship couplers for high-voltage shore connection systems (HVSC-systems) - Part 2: Dimensional compatibility and interchangeability requirements for accessories to be used by various types of ships NBN EN IEC 62631-3-11:2018 Dielectric and resistive properties of solid insulating materials - Part 3-11: Determination of resistive properties (DC methods) - Volume resistance and volume resistivity - Method for impregnation and coating materials NBN EN IEC 62677-3-101:2018 Heat-shrinkable low and medium voltage moulded shapes - Part 3: Specification for individual materials - Sheet 101: Heat-shrinkable, polyolefin moulded shapes for low voltage applications NBN EN IEC 62677-3-102:2018 Heat-shrinkable low and medium voltage moulded shapes - Part 3: Specification for individual materials - Sheet 102: Heat-shrinkable, polyolefin, anti-tracking moulded shapes for medium voltage applications NBN EN IEC 62684:2018 Interoperability specifications of common external power supply (EPS) for use with data-enabled mobile telephones NBN EN IEC 62731:2018 Text-to-speech for television - General requirements NBN EN IEC 62933-2-1:2018 Electrical energy storage (EES) systems - Part 2-1: Unit parameters and testing methods - General specification NBN EN IEC 63041-1:2018 Piezoelectric sensors - Part 1: Generic specifications NBN EN IEC 63041-2:2018 Piezoelectric sensors - Part 2: chemical and biochemical Sensors NBN EN IEC/IEEE 65700:2018 Bushings for DC application NBN EN ISO 10215:2018 Anodizing of aluminium and its alloys - Visual determination of image clarity of anodic oxidation coatings - Chart scale method (ISO 10215:2018) vervangt NBN EN ISO 10215:2010 (1e uitgave) NBN EN ISO 10364:2018 Structural adhesives - Determination of the pot life (working life) of multi-component adhesives (ISO 10364:2015) vervangt NBN EN 14022:2010 (2e uitgave) NBN EN ISO 10545-3:2018 Ceramic tiles - Part 3: Determination of water absorption, apparent porosity, apparent relative density and bulk density (ISO 10545-3:2018) vervangt NBN EN ISO 10545-3:1997 (1e uitgave) NBN EN ISO 11073-10427:2018 Health informatics - Personal health device communication - Part 10427: Device specialization - Power status monitor of personal health devices(ISO/IEEE 11073-10427:2018) NBN EN ISO 11130:2018 Corrosion of metals and alloys - Alternate immersion test in salt solution (ISO 11130:2017) vervangt NBN EN ISO 11130:2010 (2e uitgave) NBN EN ISO 11133:2014/A1:2018 Microbiology of food, animal feed and water - Preparation, production, storage and performance testing of culture media - Amendment 1 (ISO 11133:2014/Amd 1:2018) NBN EN ISO 11296-1:2018 Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks - Part 1: General (ISO 11296-1:2018) vervangt NBN EN ISO 11296-1:2011 (1e uitgave) NBN EN ISO 11297-1:2018 Plastics piping systems for renovation of underground drainage and sewerage networks under pressure - Part 1: General (ISO 11297-1:2018) vervangt NBN EN ISO 11297-1:2013 (1e uitgave) NBN EN ISO 11298-1:2018 Plastics piping systems for renovation of underground water supply networks - Part 1: General (ISO 11298-1:2018) vervangt NBN EN ISO 11298-1:2011 (1e uitgave) NBN EN ISO 11357-6:2018 Plastics - Differential scanning calorimetry (DSC) - Part 6: Determination of oxidation induction time (isothermal OIT) and oxidation induction temperature (dynamic OIT) (ISO 11357-6:2018) vervangt NBN EN ISO 11357-6:2013 (1e uitgave) NBN EN ISO 11747:2012/A1:2018 Rice - Determination of rice kernel resistance to extrusion after cooking - Amendment 1 (ISO 11747:2012/Amd 1:2017) NBN EN ISO 12570:2000/A2:2018 Hygrothermal performance of building materials and products - Determination of moisture content by drying at elevated temperature (ISO 12570:2000/Amd 2:2018) NBN EN ISO 12944-5:2018 Paints and varnishes - Corrosion protection of steel structures by protective paint systems - Part 5: Protective paint systems (ISO 12944-5:2018) vervangt NBN EN ISO 12944-5:2007 (2e uitgave) NBN EN ISO 13408-2:2018 Aseptic processing of health care products - Part 2: Sterilizing filtration (ISO 13408-2:2018) vervangt NBN EN ISO 13408-2:2011 (1e uitgave) NBN EN ISO 13485:2016/AC:2018 Medical devices - Quality management systems - Requirements for regulatory purposes (ISO 13485:2016) NBN EN ISO 14024:2018 Environmental labels and declarations - Type I environmental labelling - Principles and procedures (ISO 14024:2018) vervangt NBN EN ISO 14024:2001 (1e uitgave) NBN EN ISO 16090-1:2018 Machine tools safety - Machining centres, Milling machines, Transfer machines - Part 1: Safety requirements (ISO 16090-1:2017) vervangt NBN EN 12417+A2:2009 (2e uitgave), NBN EN 13128+A2:2009 (2e uitgave), NBN EN 14070+A1:2009 (2e uitgave) NBN EN ISO 16923:2018 Natural gas fuelling stations - CNG stations for fuelling vehicles (ISO 16923:2016) NBN EN ISO 16924:2018 Natural gas fuelling stations - LNG stations for fuelling vehicles (ISO 16924:2016) NBN EN ISO 17892-8:2018 Geotechnical investigation and testing - Laboratory testing of soil - Part 8: Unconsolidated undrained triaxial test (ISO 17892-8:2018) NBN EN ISO 17892-9:2018 Geotechnical investigation and testing - Laboratory testing of soil - Part 9: Consolidated triaxial compression tests on water saturated soils (ISO 17892-9:2018) vervangt NBN CEN ISO/TS 17892-9:2005 (1e uitgave) NBN EN ISO 19008:2018 Standard cost coding system for oil and gas production and processing facilities (ISO 19008:2016) NBN EN ISO 2081:2018 Metallic and other inorganic coatings - Electroplated coatings of zinc with supplementary treatments on iron or steel (ISO 2081:2018) vervangt NBN EN ISO 2081:2009 (1e uitgave) NBN EN ISO 21904-3:2018 Health and safety in welding and allied processes - Requirements, testing and marking of equipment for air filtration - Part 3: Determination of the capture efficiency of on-torch welding fume extraction devices (ISO 21904-3:2018) NBN EN ISO 22300:2018 Security and resilience - Vocabulary (ISO 22300:2018) vervangt NBN EN ISO 22300:2014 (1e uitgave) NBN EN ISO 26203-1:2018 Metallic materials - Tensile testing at high strain rates - Part 1: Elastic-bar-type systems (ISO 26203-1:2018) vervangt NBN EN ISO 26203-1:2010 (1e uitgave) NBN EN ISO 2819:2018 Metallic coatings on metallic substrates - Electrodeposited and chemically deposited coatings - Review of methods available for testing adhesion (ISO 2819:2017) vervangt NBN EN ISO 2819:1995 (1e uitgave) NBN EN ISO 3183:2012/A1:2018 Petroleum and natural gas industries - Steel pipe for pipeline transportation systems - Amendment 1 (ISO 3183:2012/Amd 1:2017) NBN EN ISO 4545-1:2018 Metallic materials - Knoop hardness test - Part 1: Test method (ISO 4545-1:2017) vervangt NBN EN ISO 4545-1:2006 (1e uitgave) NBN EN ISO 4545-2:2018 Metallic materials - Knoop hardness test - Part 2: Verification and calibration of testing machines (ISO 4545-2:2017) vervangt NBN EN ISO 4545-2:2006 (1e uitgave) NBN EN ISO 4545-3:2018 Metallic materials - Knoop hardness test - Part 3: Calibration of reference blocks (ISO 4545-3:2017) vervangt NBN EN ISO 4545-3:2006 (1e uitgave) NBN EN ISO 4885:2018 Ferrous materials - Heat treatments - Vocabulary (ISO 4885:2018) vervangt NBN EN ISO 4885:2017 NBN EN ISO 6507-1:2018 Metallic materials - Vickers hardness test - Part 1: Test method (ISO 6507-1:2018) vervangt NBN EN ISO 6507-1:2006 (2e uitgave) NBN EN ISO 6507-2:2018 Metallic materials - Vickers hardness test - Part 2: Verification and calibration of testing machines (ISO 6507-2:2018) vervangt NBN EN ISO 6507-2:2006 (3e uitgave) NBN EN ISO 6507-3:2018 Metallic materials - Vickers hardness test - Part 3: Calibration of reference blocks (ISO 6507-3:2018) vervangt NBN EN ISO 6507-3:2006 (2e uitgave) NBN EN ISO 6507-4:2018 Metallic materials - Vickers hardness test - Part 4: Tables of hardness values (ISO 6507-4:2018) vervangt NBN EN ISO 6507-4:2006 (1e uitgave) NBN EN ISO 7345:2018 Thermal performance of buildings and building components - Physical quantities and definitions (ISO 7345:2018) vervangt NBN EN ISO 7345:1996 (1e uitgave) NBN EN ISO 7500-1:2018 Metallic materials - Calibration and verification of static uniaxial testing machines - Part 1: Tension/compression testing machines - Calibration and verification of the force-measuring system (ISO 7500-1:2018) vervangt NBN EN ISO 7500-1:2016 NBN EN ISO 7668:2018 Anodizing of aluminium and its alloys - Measurement of specular reflectance and specular gloss of anodic oxidation coatings at angles of 20 degrees, 45 degrees, 60 degrees or 85 degrees (ISO 7668:2018) vervangt NBN EN ISO 7668:2010 (1e uitgave) NBN EN ISO 7886-1:2018 Sterile hypodermic syringes for single use - Part 1: Syringes for manual use (ISO 7886-1:2017) vervangt NBN EN ISO 7886-1:1997 (1e uitgave) NBN EN ISO 8442-9:2018 Materials and articles in contact with foodstuffs - Cutlery and table holloware - Part 9: Requirements for ceramic knives (ISO 8442-9:2018) NBN EN ISO 8654:2018 Jewellery - Colours of gold alloys - Definition, range of colours and designation (ISO 8654:2018) vervangt NBN EN 28654:1993 (1e uitgave) 2. De normen afgeleid van de Europese normen (EN) zijn in principe beschikbaar in het Engels, het Frans en het Duits;de normen afgeleid van de internationale normen (ISO) zijn in principe beschikbaar in het Engels en in het Frans. 3. Deze normen zijn verkrijgbaar bij het Bureau voor normalisatie, Jozef II-straat 40 bus 6, 1000 Brussel, tegen betaling van hun prijs. 4. De registratie van de volgende Belgische normen wordt ingetrokken: NBN EN 12691:2006 (2e uitgave) NBN EN 13463-2:2005 (1e uitgave) NBN EN 13463-3:2005 (1e uitgave) NBN EN 14727:2006 (1e uitgave) NBN EN 4165-001:2015/AC:2016 NBN EN 50133-7:2000 (1e uitgave) NBN EN 60079-6:2007 (4e uitgave) NBN EN 60627:2002 (2e uitgave) NBN EN 61202-1:2009 (2e uitgave) NBN EN 61285:2005 (1e uitgave) NBN EN 62366/A1:2015 (1e uitgave) NBN EN 62366:2008 (1e uitgave) NBN EN 786+A2:2010 (2e uitgave) NBN EN ISO 13485:2016/AC:2017

^